Product Center 产品中心

新品推荐

当前位置: 首页 > 新品推荐
 BE14 耐潮湿无溶剂型环氧底漆
来源: 点击数:380次 更新时间:2019-5-11 17:38:39
BE14
产品名称:OMELON BE14
产品介绍:
GENERAL
BE14, is an excellent 100% solid epoxy primer for concrete surfaces. BE14, is ecologically and designed for application directly On wet and dry surfaces It is compatible with new(green) or aged Concrete, bare concrete or existing coatings that are firmly adhered To surface.
总述
BE14 是一种固含量为100%的优异的环氧底漆,用于混凝土的表面。BE14 可直接涂装在湿的或干的表面,与新旧混凝土相容。与裸露的混土或有涂层的混凝土能紧紧附着。
FEATRURES

NO HARMFUL SOLVENT VAPOURS.

NON-FLAMMABLE.

Good chemical resistance

No more problems with DEW POINT.

Fast drying

Excellent substrate and intercoat adhesion either on wet or dry surface.

Cost savings on surface preparation.

产品特性

无有害挥发物

不可燃

良好的耐化学性

无露点问题

快干

不论是湿的还是干的表面,与基底或中间涂层有优异的粘接力

节省表面处理成本

RECOMMENDED
USES TYPICAL STRUCTURES Concrete pylons; Sea walls; Pools and Sea aquarium; Dams and Concrete locks; Aqueducts; Concrete tanks-water, Fuel or Grains; Tunnels; etc. SHIPS, OFFSHORE Decks, Chain lockers, Tower bridge, etc. PIPE COATINGS Suitable for direct application on exterior and interior potable water Pipes lines. Sew lines. Excellent chemical resistance.
推荐用途
典型结构
混凝土的标塔,海堤,池子,防水层,大坝,水闸,高架水道,混凝储水罐,燃料或各种的储存罐,隧道。船只,港口甲板,链锁装置,塔,桥等。管道涂层适用于饮水管道内外壁的涂层,良好的耐化学性。
SPECIFICATION DATA
技 术 参 数
Binder Type/Pigment Type
Modified epoxy/Amine composite- Chemical resistant pigments
基料类型/颜料类型
改性环氧/复合胺/耐化学型颜料
Colors
BE1409(clear), BE1410(light grey) BE1411(dark grey)
颜色
BE14 09透明,BE14 10浅灰色,BE1411深灰
Finish
Gloss
表面
高光
Mixing ratio
4base) to 1(curing agent) by weight, 3.3(base) to1(curing agent) by volume
混合比率
重量比 4(基料):1(固化剂)
体积比 3.3(基料):1(固化剂)
Curing agent
CA24
固化剂
CA24
Specific gravity(mixture-BE1409)
1.09±0.02Kg/ Lt
比重
1.09±0.02公斤/升
Solid by Volume
100%(theoretical)
体积固体份
100%(理论值)
Pot Life
10 minutes at 23℃(73.4℉)
混合使用期
10分钟,23℃(73.4℉)
Flash point(Abel)
Base: >100℃(>212℉);Curing agent: >100℃(>212℉)
闪点
基料:>100℃;固化剂:>100℃
Theoretical covering capability
4.6Sq.m/Kg(22.4 q.ft/Lb) at 200 microns (8 mils)
理论覆盖能力
4.6平方米/公斤,200um
Typical film thickness per coat
Wet:200microns(8mils); Dry:200 mircons (8mils)
单层膜厚
湿膜:200um,干膜:200um
Application method
Brush, Roller
施工方法
刷子,辊子
Thinner
Material: none -Cleaning: EURO-thinner TH03
稀释剂
材料:无;清洗:TH03
VOC
Does not contain. It is a 100% solids epoxy product.
挥发性有机化合物
不含,为100%的固体环氧产品。
Drying time
Surface dry: approx. 3 hours (at 23℃ (73.4℉) and 50% relative humidity)
干燥时间
表干:3小时,在23°C和50%相对湿度下。
Overcoating time
Min:16 hours at 23℃ ;Max: 7 days.
重涂时间
最短:16小时(23°C),最长:7天.
Ambient temperature
Min: >0℃(32℉)-Max: Not applicable. Substrate is the important factor when applying below 0℃(32℉), a different cure is required.
环境温度
最低:>0°C,最高:无,基底是重要因素。当于0℃以下涂覆时,要求不同的固化方法。
Substrate temperature
Min:0℃(32℉)- Max:50℃(122℉)
底材温度
最低:0°C,最高:50°C
Storage and Shelf life
The product should be kept in a cool well ventilated places
protected from high temperatures.
Container MUST BE kept tightly closed.
Shelf life:1 year
包装和储存期限
产品保存于阴凉、通风良好的地方,避
免过高的温度。容器必须牢固密封.储存期:1年
APPLICATION GUIDE
施 工 指 导
SURFACE PREPARATION
BE14, is designed for application over concrete surfaces pre-treated by Hydrojetting, mechanical cleaning, and wet or dry abrasive blasting to standards specified. Coating performance is, in general, proportional to degree of surface preparation.
表面处理
BE14,用于经过高压水或机械清洗的混凝土表面 。一般,涂层的性能与表面处理的级别成正比
APPLICATION
BE14, can be applied, by brush and roller. Ventilation It is very important for the safety of the applicator that good ventilation be provided to all portions of the area.
施工
BE14,可采用刷涂、辊涂
通风
作业区的各个部位保持良好的通风对操作人员的安全是非常重要的。
SAFETY
WARNING: Avoid breathing vapors. Do not get in eyes on skin or clothing, Use ear ,eye and skin protective equipment. Use appropriate respirator. Wash skin thoroughly after use and water. Launder clothing before reuse. If not breathing gives artificial respiration, preferably mouth-to-mouth, and call physician.
BURNS: Exothermic reaction causes product to heat which is normal.
Be careful handling after mixing product. Use gloves.
FIRST AID: In case of eye contact immediately flush with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash skin contact area with soap.
安全措施
警告:避免吸入汽雾。请勿触及眼睛皮肤。要使用眼、耳、皮肤的防护用具,使用合适的面具。使用后用清水彻底的清洗皮肤。衣物再次使用前要洗涤。如果没有呼吸要进行人工呼吸,最好嘴对嘴,并请医生处理。
灼伤:放热反应会使产品变热,超出正常水平。在混合后要小心处理。使用手套。
急救:如果不慎接触了眼睛,立即用清水冲洗至少15分钟,并脱去污染的衣鞋,用肥皂清洗接触后的皮肤。
DISCLAMER
This is not a specification and all information is given in good faith. Every values presented as Theoretical were calculated from the product formula If requested, Euronavy can inform any internal measurement method used to determinate any given value presented. Since conditions of use are beyond the manufacturers control information contained herein is without warranty, implied or otherwise, and final determination of the suitability of any information or material for the use contemplated is the sole responsibility of user. The product is intended for professional use only. In case of any doubt, contact your local agent.
提请注意
此文件不是正式的技术文件,所列出的信息是可靠的。提供的每个数值都是作为理论数据从产品的配方中计算出来的。如果需要,Euronavy可以告知任何上述给出数据的内部常用测量确定方法。由于使用条件非生产商所能控制,这里的信息不作为担保。产品仅限于专业人员使用。如有任何问题,请与当地相关机构联系。
【刷新页面】【加入收藏】【打印此文】 【关闭窗口】
上一篇:ES301 无溶剂耐潮湿型环氧涂料 下一篇:ES323 无溶剂型水下环氧涂料