Product Center 产品中心

产品中心

当前位置: 首页 > 产品中心
 BE23 无溶剂型环氧厚膜复合涂料
来源: 点击数:1693次 更新时间:2023-7-7 11:08:56

产品名称:OMELON BE23
产品介绍:
GENERAL BE23, is a 100% solids epoxy compound that , after mixing with silica, produces an excellent epoxy mortar. BE23, is ecologically and designed for application in Concrete or steel surfaces. The surfaces must be treated with a Suitable primer before application. BE23, is recommended in floors that must be resistant to Abrasion, impact, chemicals. When different coloured silica’s are Used, the floorings have an increased cosmetic effect.
总述 BE23 是100% 固含量的环氧复合涂料,与二氧化硅搅拌后制成优异的环氧砂浆. BE23 用于混凝土或钢表面的涂覆,在涂覆前,表面必须用合适的底漆处理. BE23推荐用于须耐磨、耐冲击、耐化学药品的各种地坪,当使用不同的颜色,会增加装饰效果
FEATRURES

NO HARMFUL SOLVENT VAPOURS.

NO VOC’s

Superior impact resistance.

NON-FLAMMABLE.

Good chemical resistance.

Can be used in the food industry.

Good cosmetic effect.

产品特性

无有害挥发物

无挥发性有机化合物

卓越抗冲击强度

不可燃

优良的耐化学性

可用于食品工业

优良的装饰效果

RECOMMENDED USES FLOORS ON STEEL OR CONCRETE Industrial floorings. Anti-skid floorings. Food industry. Warehouses. Decks. Recovering of badly corroded (pitted) steel.
推荐用途 钢或混凝土上的地坪 工业地坪 抗滑地坪 食品工业 仓库 甲板 修复严重点蚀的钢板
SPECIFICATION DATA 技 术 参 数
Binder Type/Pigment Type Modified epoxy/Amine composite
基料类型/颜料类型 改性环氧/复合胺
Colors Transparent
颜色 透明
Finish Gloss
表面 高光
Mixing ratio 3.3(base) to 1(curing agent) by weight,3(base) to1(curing agent) by volume
混合比率 重量比 3.3(基料):1(固化剂) 体积比 3(基料):1(固化剂)
Curing agent CA14
固化剂 CA14
Specific gravity(mixture) 1.10±0.02Kg/ Lt
比重 1.10±0.02公斤/升
Solid by Volume 100%(theoretical)
体积固体份 100%(理论值)
Pot Life 12 minutes at 23℃(73.4℉)
活性期 12分钟,23℃(73.4℉)
Flash point(Abel) Base: >100℃(>212℉);Curing agent: >100℃(>212℉)
闪点 基料:>100℃; 固化剂:>100℃
Theoretical covering capability Mortar: 1 part of EURO-steel BE23 mixture to 6 parts of silica(IN01)
6.6Kg/ m2 at 3mm; 13.2Kg/m2 at 6mm. BE23 as a primer 0.22 Kg/m2 at 200 microns (8 mils).
理论覆盖能力 砂浆:1份BE23与6份硅(IN01)混合,3毫米膜厚6.6公斤/平方米,6毫米膜厚13.2公斤/平方米,. BE23作底漆:0.22公斤/平方米,200um厚
Typical film thickness per coat Mortar:3mm to 6mm; Primer:200 microns (8mils)
单层膜厚 厚浆:3-6毫米,底漆:200um
Application method Trowel, spreader, squeegee, or other specific equipment for mortar application.
施工方法 镘刀、涂布器、橡胶辊子或其他厚浆涂覆专用设备
Thinner Material: none -Cleaning: EURO-thinner TH03
稀释剂 材料:无;清洗:TH03
VOC Does not contain. It is a 100% solids epoxy product.
挥发性有机化合物 不含,为100%的固体环氧产品
Drying time Surface dry: approx. 4 hours (at 23℃ (73.4℉) and 50% relative humidity)
干燥时间 指干:4小时,在23°C和50%相对湿度下。
Overcoating time Min:16 hours at 23℃ ;Max: 7 days.
涂装时间 最短:16小时(23°C),最长:7天。
Recommended primers Dry concrete: EURO-steel BE23, EURO-pox I PE05 Wet concrete:EURO-floor ES302 clear; Steel: EURO-basic ES301
推荐底漆 干混凝土:BE23,PE05;湿混凝土:ES302清漆;钢:ES301
Ambient temperature Min: >0℃(32℉)-Max: 40℃(104℉)
环境温度 最低:>0°C,最高:40°C
Substrate temperature Min:0℃(32℉)- Max:40℃(104℉)
底材温度 最低:0°C,最高:40°C
Storage and Shelf life
储存及有效期:
The product should be kept in a cool well ventilated places protected from high temperatures. Container MUST BE kept tightly closed. Shelf life:1 year 产品保存于阴凉、通风良好的地方,避 免过高的温度。 容器必须牢固密封。有效期:1年。
APPLICATION GUIDE 施 工 指 导
SURFACE PREPARATION BE23, as a primer, remove all the materials by mechanical methods, remove completely all the coatings previously applied. All surfaces must be free of oil, grease, dust, and other foreign matter before application. BE23, as a mortar, can be applied on concrete and steel treated with a suitable primer, all surfaces must be free of oil, grease, moisture, dust and other foreign matter before application.
表面处理 BE23,作为底涂料,采用机械方法去除所有杂物和旧漆膜。涂装前所有的表面必须没有油脂、水汽和杂质。 BE23,做为砂浆,适用于涂有底漆的混凝土和钢表面上,所有的表面涂装前必须无油脂、水汽、尘土和杂质。
APPLICATION BE23, as a primer can be applied with a roller. BE23, as a mortar, must be applied with a trowel, spreader, squeegee, or other specific equipment for mortar application. Care should be taken that uniform film thickness is obtained. The mortar must be sealed (Min. 24 hrs. after application) with the BE23. Ventilation It is very important for the safety of the applicator that good ventilation be provided to all portions of the area.
施工 BE23,作为底漆可以辊涂。 BE23,作为砂浆必须用镘子、涂布器或特殊的设备进行施工。注意得到正确均匀的膜厚。 涂装后厚浆涂层必须用EURO-BE23进行封闭(厚浆涂装最少24小时内封闭)。 通风 作业区的各个部位保持良好的通风对操作人员的安全是非常重要的。
SAFETY WARNING: Avoid breathing vapors. Do not get in eyes on skin or clothing, Use ear ,eye and skin protective equipment. Use appropriate respirator. Wash skin thoroughly after use and water. Launder clothing before reuse. If not breathing gives artificial respiration, preferably mouth-to-mouth, and call physician. BURNS: Exothermic reaction causes product to heat which is normal. Be careful handling after mixing product. Use gloves. FIRST AID: In case of eye contact immediately flush with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash skin contact area with soap.
安全措施 警告:避免吸入汽雾。请勿触及眼睛皮肤。要使用眼、耳、皮肤的防护用具,使用合适的面具。使用后用清水彻底的清洗皮肤。衣物再次使用前要洗涤。如果没有呼吸要进行人工呼吸,最好嘴对嘴,并请医生处理。 灼伤:放热反应会使产品变热,超出正常水平。在混合后要小心处理。使用手套。 急救:如果不慎接触了眼睛,立即用清水冲洗至少15分钟,并脱去污染的衣鞋,用肥皂清洗接触后的皮肤。
DISCLAMER This is not a specification and all information is given in good faith. Every values presented as Theoretical were calculated from the product formula If requested, Euronavy can inform any internal measurement method used to determinate any given value presented. Since conditions of use are beyond the manufacturers control information contained herein is without warranty, implied or otherwise, and final determination of the suitability of any information or material for the use contemplated is the sole responsibility of user. The product is intended for professional use only. In case of any doubt, contact your local agent.
提请注意 此文件不是正式的技术文件,所列出的信息是可靠的。提供的每个数值都是作为理论数据从产品的配方中计算出来的。如果需要,Euronavy可以告知任何上述给出数据的内部常用测量确定方法。由于使用条件非生产商所能控制,这里的信息不作为担保。产品仅限于专业人员使用。如有任何问题,请与当地E相关机构联系。
【刷新页面】【加入收藏】【打印此文】 【关闭窗口】
上一篇:没有了 下一篇:BE14 耐潮湿无溶剂型环氧底漆