|
GENERAL
|
BE07, is an excellent 100% epoxy self-leveling, for application on steel, aluminum and concrete surfaces. EURO-freezer BE07, is ecologically and designed to achieve a good Combination of elasticity, high mechanical strength and chemical Resistance. EURO-freezer BE07, has a superior elasticity. Due to his outstanding Properties can be used inside the refrigerating compartments(-25℃ Up to 40℃)
|
|
总述
|
BE07 是性能优异的无溶剂环氧自流平涂料,适用于钢,铝和混凝土表面。BE07 是生态环保设计，具有高弹性，机械强度高，耐化学品性优良的综合性能。BE07 具有很高的弹性,具备使用温度范围广泛特殊的性能,可用于制冷室的内部(从-25°C高达40°C)。
|
|
FEATRURES
|
NO HARMFUL SOLVENT VAPOURS.
NO VOC’s
Superior elasticity and mechanical strength properties.
NON-FLAMMABLE.
Good chemical, solvent and water immersion resistance.
Applications up to 1.18” tick on horizontal surfaces.
Easy overcoating with polyurethane.
|
|
产品特性
|
无有害挥发物
无挥发性有机化合物
优秀的弹性和机械性能
不可燃
具耐化学品，耐溶剂，耐水浸泡的优良性能
在水平面上可涂装高达1.18英寸的厚度
易于聚氨脂涂料覆涂。
|
|
RECOMMENDED USES
|
SHIPS REFRIGERATING COMPARTMENTS.
INDUSTRIAL REFRIGERATING COMPARTMENTS.
OFFSHORES REFRIGERATING COMPARTMENTS.
TRUCK REFRIGERATING COMPARTMENTS.
|
|
推荐用途
|
货车制冷室
|
|
SPECIFICATION DATA
|
|
技 术 参 数
|
|
Binder Type/Pigment Type
|
Modified epoxy/Amine composite- Chemical resistant pigments＆extenders.
|
|
基料类型/颜料类型
|
改性环氧/复合胺，耐化学性颜填料
|
|
Colors
|
BE0710(light grey)
|
|
颜色
|
BE0710(浅灰色)
|
|
Finish
|
Semi-gloss
|
|
表面
|
半光
|
|
Mixing ratio
|
8.4(base) to 1(curing agent) by weight, 5(base) to 1(curing agent) by volume.
|
|
混合比率
|
重量比8.4(基料)：1(固化剂)； 体积比5(基料)：1(固化剂),
|
|
Curing agent
|
CA14
|
|
固化剂
|
CA14
|
|
Specific gravity
|
1.58±0.03Kg/ Lt
|
|
比重
|
1.58±0.03公斤/升
|
|
Solid by Volume
|
100%(theoretical)
|
|
体积固体份
|
100%(理论值)
|
|
Pot Life
|
10 minutes at 23℃(73.4℉)
|
|
混合使用期
|
10分钟，23℃(73.4℉)
|
|
Flash point(Abel)
|
Base: >100℃(>212℉);Curing agent: >100℃(>212℉)
|
|
闪点
|
基料：>100℃; 固化剂： >100℃
|
|
Theoretical covering capability
|
0.21Sq.m/Kg(1.03q.ft/Lb) at 3000 microns (120 mils)
|
|
理论覆盖能力
|
0.21平方米/公斤,3000um厚
|
|
Typical film thickness per coat
|
Wet:3000 microns(120 mils); Dry:3000 microns (120mils)
|
|
单层膜厚
|
湿膜：3000um，干膜：3000um
|
|
Thinner
|
Material: none -Cleaning: EURO-thinner TH03
|
|
稀释剂
|
材料：无；清洗剂：TH03
|
|
VOC .
|
Does not contain. It is a 100% solids epoxy product
|
|
挥发性有机化合物
|
不含，为100%的固体环氧产品。
|
|
Drying time
|
Surface dry: approx. 3 hours (at 23℃ （73.4℉） and 50% relative humidity)
|
|
干燥时间
|
表干：3小时, 在23°C和50%相对湿度下
|
|
Overcoating time
|
Min:16 hours at 23℃ ;Max: 7 days at 23℃ （73.4℉）
|
|
重涂时间
|
最短：16小时，在23°C下，最长：7天,在23°C下
|
|
Recommended primers
|
Steel: EURO-basic ES301, Concrete: EURO-floor ES302 clear (wet) EURO-steel BE23 (dry)
|
|
推荐底漆
|
钢： ES301 , 混凝土： ES302潮湿表面, BE23干燥表面
|
|
Ambient temperature
|
Min: >5℃(41℉)-Max: Not applicable. Substrate is the important factor when applying below 5℃(41℉), a different cure is required.
|
|
环境温度
|
最低：>5°C，最高：无,基底是重要因素,当温度低于于5°C以下涂覆时,要求不同的固化方法。
|
|
Substrate temperature
|
Min:0℃(32℉)- Max:50℃(122℉)
|
|
底材温度
|
最低：0°C，最高：50°C
|
|
Storage and Shelf life
|
The product should be kept in a cool well ventilated places
protected from high temperatures.
Container MUST BE kept tightly closed.
Shelf life:1 year
|
|
储存及有效期
|
产品保存于阴凉、通风良好的地方，避
免过高的温度。容器必须牢固密封。 有效期：1年。
|
|
APPLICATION GUIDE
施 工 指 导
|
|
|
SURFACE PREPARATION
|
BE07, is designed for application on horizontal
concrete surfaces over a suitable primer.
EURO-freezer BE07, must be applied on surfaces without dust, oil,
Grease and other contaminations.
|
|
表面处理
|
BE07，用于涂有适当底漆的水平混凝土表面。
BE07，必须涂覆在没有尘土、油脂和其它污染物的表面上。
|
|
APPLICATION
|
BE07, can be applied, by trowel, spreader, squeegee or
roller. Care should be taken that proper and uniform film thickness is
obtained.
BE07, can be applied up to 3 cm (1,18”), tick on
horizontal surfaces. A minimum of two days cure should be allowed
Before floor is put into service. Product may be applied on wet or
Dry surfaces in 100% humidity conditions.
Ventilation
It is very important for the safety of the applicator and the proper performance of EURO- freezer BE07, that good ventilation be provided to all portions of the enclosed area. Dry air IS NOT a must since EURO- freezer BE07. DOES NOT contain solvents, can be applied under severe conditions of humidity.
|
|
施工
|
BE07，可采用刮涂、辊涂。注意得到正确的且均匀的膜厚。
BE07，可以在水平面上涂装厚度高达3公分。地坪在使用之前应该有至少两天的固化时间，产品可以在湿的或干的表面上，在湿度为100%的条件下涂装。
通风
作业区的各个部位保持良好的通风对操作人员的安全和施工效果都是非常重要的。 空气不一定要干燥，由于本产品不含溶剂，可以在严酷的湿度条件下涂覆施工。
|
|
SAFETY
|
WARNING:
Avoid breathing vapors. Do not get in eyes on skin or clothing, Use ear ,eye and skin protective equipment. Use appropriate respirator. Wash skin thoroughly after use and water. Launder clothing before reuse. If not breathing gives artificial respiration, preferably mouth-to-mouth, and call physician.
BURNS: Exothermic reaction causes product to heat which is normal.
Be careful handling after mixing product. Use gloves.
FIRST AID: In case of eye contact immediately flush with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash skin contact area with soap.
|
|
安全措施
|
警告：避免吸入汽雾。请勿触及眼睛皮肤。要使用眼、耳、皮肤的防护用具，使用合适的面具。使用后用清水彻底的清洗皮肤。衣物再次使用前要洗涤。如果没有呼吸要进行人工呼吸，最好嘴对嘴，并请医生处理。
灼伤：放热反应会使产品变热，超出正常水平。在混合后要小心处理。使用手套。
急救：如果不慎接触了眼睛，立即用清水冲洗至少15分钟，并脱去污染的衣鞋，用肥皂清洗接触后的皮肤。
|
|
DISCLAMER
|
This is not a specification and all information is given in good
faith. Every values presented as Theoretical were calculated from the product formula If requested, Euronavy can inform any internal measurement method used to determinate any given value presented. Since conditions of use are beyond the manufacturers control information contained herein is without warranty, implied or otherwise, and final determination of the suitability of any information or material for the use contemplated is the sole responsibility of user. The product is intended for professional use only. In case of any doubt, contact your local agent.
|
|
提请注意
|
此文件不是正式的技术文件，所列出的信息是可靠的。提供的每个数值都是作为理论数据从产品的配方中计算出来的。如果需要，Euronavy可以告知任何上述给出数据的内部常用测量确定方法。由于使用条件非生产商所能控制，这里的信息不作为担保。产品仅限于专业人员使用。如有任何问题，请与当地相关机构联系。
|
