Product Center 产品中心

产品中心

当前位置: 首页 > 产品中心
 BE06 无溶剂型自流平环氧地坪漆
来源: 点击数:1511次 更新时间:2023-7-7 11:13:17

产品名称:OMELON BE06
产品介绍:
GENERAL
BE06, is an excellent 100% epoxy flooring self-levelling, with impact resistance and chemical resistance, for application on concrete surfaces.BE06, is ecologically and designed for filling losses of Concrete. EURO-level 2 BE06, MUST BE applied overES302 clear (wet surfaces), or EURO-steel BE23 (dry surfaces).
总述
BE06 是一种优异的100%环氧的自流平的涂料,具有抗冲击性,抗化学性,用于混凝土表面的涂装. BE06 从生态上设计,用来填充混凝土的缺损部分. BE06 它必须涂装在EURO-floor ES302 (湿表面),或BE23(干表面)涂层的上面.
FEATRURES

NO HARMFUL SOLVENT VAPOURS.

NO VOC’s

Superior impact resistance.

NON-FLAMMABLE.

Good chemical, solvent and water immersion resistance.

No more problems with DEW POINT.

Applications up to 1.18” tick on horizontal surfaces.

Cost savings on surface preparation.

Excellent protective properties.

产品特性

无有害挥发物

无挥发性有机化合物

高抗冲击性能

不可燃

具耐化学品,耐溶剂,耐水浸泡的优良性能

无露点限制

在水平面上可涂装高达1.18英寸的厚度

节省表面处理的成本

优异的保护性

RECOMMENDED USES

REPAIR OF CONCRETE BOTTOM TANKS

Potable water tanks.

Selected chemical tanks.

INDUSTRIAL FLOORS.

Glass factories.

Food factories.

Car factories.

Schools.

Workshops.

推荐用途
修复混凝土底罐

饮用水罐

部分化学品罐

工业地坪

玻璃厂

食品厂

汽车厂

学校

车间

SPECIFICATION DATA
技 术 参 数
Binder Type/Pigment Type
Modified epoxy/Amine composite- Chemical resistant pigments&extenders.
基料类型/颜料类型
改性环氧/复合胺,耐化学颜填料
Colors
BE0600(white), BE0699(black), BE0610(grey), or custom request.
颜色
BE0600(白色),BE0699(黑色),BE0610(灰色)或用户要求
Finish
Gloss
表面
高光
Mixing ratio
5(base) to 1(curing agent) by weight, 3.1(base) to 1(curing agent) by volume.
混合比率
重量比5(基料):1(固化剂),体积比3.3(基料):1(固化剂)。
Curing agent
CA14
固化剂
CA14
Specific gravity
1.41±0.03Kg/ Lt
比重
1.41±0.03公斤/升
Solid by Volume
100%(theoretical)
体积固体份
100%(理论值)
Pot Life
30 minutes at 23℃(73.4℉)
混合使用期
30分钟,23℃(73.4℉)
Flash point(Abel)
Base: >100℃(>212℉);Curing agent: >100℃(>212℉)
闪点
基料:>100℃; 固化剂:>100℃
Theoretical covering capability
0.28Sq.m/kg.(1.38 q.ft/Lb) at 25 microns (100 mils)
理论覆盖能力
0.28平方米公斤,2500um厚
Typical film thickness per coat
Wet:2500 microns(100 mils); Dry:2500 mircons (100mils)
每层膜厚
湿膜:2500um,干膜:2500um
Thinner
Material: none -Cleaning: EURO-thinner TH03
稀释剂
材料:无; 清洗剂:TH03
VOC
Does not contain. It is a 100% solids epoxy product.
挥发性有机化合物
不含,为100%的固体环氧产品。
Drying time
Surface dry: approx. 3 hours (at 23℃ (73.4℉) and 50% relative hunidity)
干燥时间
表干:3小时,在23°C和50%相对湿度下。
Overcoating time
Min:16 hours at 23℃ ;Max: 7 days at 23℃ (73.4℉)
重涂时间
最短:16小时,在23°C下。最长:7天在23°C下。
Recommended primers
EURO-floor ES302 clear (wet), EURO-steel BE23 (dry)
推荐底漆
ES302 潮湿表面, BE23干燥表面
Ambient temperature
Min: >5℃(41℉)-Max: Not applicable. Substrate is the important factor when applying below 5℃(41℉), a different cure is required.
环境温度
最低:>5°C,最高:无,,基底是重要因素,当于5°C以下涂覆时要求不同的固化方法。
Substrate temperature
Min:0℃(32℉)- Max:50℃(122℉)
底材温度
最低:0°C,最高:50°C
Storage and Shelf life
The product should be kept in a cool well ventilated places protected from high temperatures. Container MUST BE kept tightly closed. Shelf life:1 year
储存及有效期
产品应保存于阴凉、通风良好的地方,避免过高的温度。容器必须牢固密封。有效期:1年 。
APPLICATION GUIDE
施 工 指 导
SURFACE PREPARATION
BE06, is designed for application on horizontal concrete surfaces over a suitable primer. EURO-level 2 BE06, must be applied on surfaces without dust, oil, Grease and other contaminations.
表面处理
BE06,用于涂有适当底漆的水平混凝土表面。BE06,必须涂覆在没有尘土、油脂和其它污染物的表面上。
APPLICATION
BE06, can be applied, by trowel, spreader, squeegee or roller. Care should be taken that proper and uniform film thickness is obtained. BE06, can be applied up to 3 cm (1,18”), tick on Horizontal surfaces. A minimum of two days cure should be allowed Before floor is put into service. Product may be applied on wet or Dry surfaces in 100% humidity conditions. Ventilation It is very important for the safety of the applicator and the proper performance of EURO-level 2 BE06, that good ventilation be provided to all portions of the enclosed area. Dry air IS NOT a must since EURO-level 2 BE06. DOES NOT contain solvents, can be applied under severe conditions of humidity.
施工
BE06,可采用刮涂、辊涂。注意得到正确的且均匀的膜厚。
BE06,可以在水平面上涂装厚度高达3公分。地坪在使用之前应该有至少两天的固化时间,产品可以在湿的或干的表面上,在湿度为100%的条件下涂装。
通风
作业区的各个部位保持良好的通风对操作人员的安全和施工效果都是非常重要的。 空气不一定要干燥,由于本产品不含溶剂,可以在严酷的湿度条件下涂覆施工。
SAFETY
WARNING: Avoid breathing vapors. Do not get in eyes on skin or clothing, Use ear ,eye and skin protective equipment. Use appropriate respirator. Wash skin thoroughly after use and water. Launder clothing before reuse. If not breathing gives artificial respiration, preferably mouth-to-mouth, and call physician.
BURNS: Exothermic reaction causes product to heat which is normal.
Be careful handling after mixing product. Use gloves.
FIRST AID: In case of eye contact immediately flush with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash skin contact area with soap.
安全措施
警告:避免吸入汽雾。请勿触及眼睛皮肤。要使用眼、耳、皮肤的防护用具,使用合适的面具。使用后用清水彻底的清洗皮肤。衣物再次使用前要洗涤。如果没有呼吸要进行人工呼吸,最好嘴对嘴,并请医生处理。
灼伤:放热反应会使产品变热,超出正常水平。在混合后要小心处理。使用手套。
急救:如果不慎接触了眼睛,立即用清水冲洗至少15分钟,并脱去污染的衣鞋,用肥皂清洗接触后的皮肤。
DISCLAMER
This is not a specification and all information is given in good faith. Every values presented as Theoretical were calculated from the product formula If requested, Euronavy can inform any internal measurement method used to determinate any given value presented. Since conditions of use are beyond the manufacturers control information contained herein is without warranty, implied or otherwise, and final determination of the suitability of any information or material for the use contemplated is the sole responsibility of user. The product is intended for professional use only. In case of any doubt, contact your local agent.
提请注意
此文件不是正式的技术文件,所列出的信息是可靠的。提供的每个数值都是作为理论数据从产品的配方中计算出来的。如果需要,Euronavy可以告知任何上述给出数据的内部常用测量确定方法。由于使用条件非生产商所能控制,这里的信息不作为担保。产品仅限于专业人员使用。如有任何问题,请与当地相关机构联系。
【刷新页面】【加入收藏】【打印此文】 【关闭窗口】
上一篇:BE07 无溶剂型环氧弹性涂料 下一篇:TH03 环氧稀释剂