|
GENERAL
|
PE07 can used be an anti-corrosive coating or additional layer for anticorrosive coating. which will enhance sealing and anti-corrosion properties. It’s possessed of higher sealing property. In addition, it forms a coating with good resistance to heat and corrosion , this paint is able to match with most pain
|
|
总述
|
PE07 可用做防锈底漆，也可作为防锈漆的加涂层。增加封闭性和防腐蚀性能。具有较高的封闭性，耐热性和防腐性良好。与大多数涂料配套。
|
|
RECOMMENDED USES
|
steel structure
|
|
推荐用途
|
适用于各种钢结构
|
|
SPECIFICATION DATA
|
|
|
技 术 参 数
|
|
|
Vehicle Type/Pigment Type
|
Modified epoxy
|
|
漆料类型/颜料类型
|
改性环氧
|
|
Colors .
|
grey
|
|
颜色
|
灰
|
|
Mixing ratio
|
By weight: 10(base) to 1(curing agent);
|
|
混合比率
|
重量比10(基料)：1(固化剂)
|
|
Curing agent
|
PE07C01
|
|
固化剂
|
PE07C01
|
|
Specific gravity(mixture)
|
1.42±0.05Kg/dm3 (23℃/73.4℉)
|
|
比
|
重 1.42±0.05公斤/立方分米
|
|
Volume of Solids
|
65% （Theoretical）
|
|
体积固体份
|
65%(理论上)
|
|
Flash point(Abel)
|
Base:>23℃;Curing agent:>40℃
|
|
闪点
|
基底>23℃；固化剂：>40℃
|
|
Theoretical covering capability
|
6.5 Sq.m/Lt. at 100 microns (4mils)
|
|
理论覆盖能力
|
6.5平方米/ 升
|
|
Typical film thickness per coat
|
Wet:154 microns (6 mils) ; Dry:100 microns (4mils)
|
|
单层膜厚
|
湿膜：154um；干膜：100um
|
|
Application
|
method Brush, Roller or Airless Spray
|
|
施工方法
|
手刷、滚轮刷、无气喷涂
|
|
Thinner
|
Product: TH03- Cleaning: TH03
|
|
稀释剂
|
产品：TH03； 清洁剂：TH03
|
|
V.O.C
|
285 grams/Lt.
|
|
挥发性有机化合物
|
285克/升.
|
|
Pot Life
|
(at 23℃/73.4℉) 8h at 23℃(73.4℉)
|
|
混合使用期
|
23℃(73.4℉)时8h
|
|
Drying time
|
Surface dry: 2 hours at 23℃(73.4℉)
|
|
干燥时间
|
表干：23℃(73.4℉)时2小时
|
|
Overcoating time
|
Min:10 hours at 23℃(73.4℉); Max:7 days. If maximum overcoat
|
|
重涂时间
|
最短：23℃(73.4℉)时10小时；最长：7天。
|
|
Ambient temperature
|
Min : 5℃(41℉) ;Max:40℃(104℉)
|
|
环境温度
|
最低：5°C；最高40°C
|
|
Substrate temperature
|
Min : 5℃(41℉) ;Max:40℃(104℉)
|
|
底材温度
|
最低：5°C；最高40°C
|
|
Packing
|
Product is a two pack component, available in 1,5 and 20 Kg combined packs.
|
|
包装
|
双组份 ,包装规格有1，5，20公斤包装
|
|
Storage conditions
|
The product must be stored in accordance with national regulations. The product should be kept in a cool well ventilated places protected f rom high temperatures. Containers MUST BE kept tightly closed. Shelf life: 1 year.
|
|
储存及有效期
|
产品储存必须和国际准则一致。产品应在良好的 通风处保存，防止高温。容器必须保持紧紧关严。 有效期：1年。
|
|
APPLICATION GUIDE
|
|
|
施 工 指 导
|
|
|
SURFACE
|
PE07, is designed for application directly to iron/ steel surfaces pre-treated by Blast cleaning to Sa2.5 of the Swedish SIS 0055900. All surfaces must be free of oil, grease, moisture another foreign matter prior to blasting.
|
|
表面处理
|
PE07 设计用于在钢铁表面经喷砂预处理达到 瑞典标准SIS055900的Sa2.5级后直接涂装。 所有表面必须无油脂、水分或其它杂质，然后才能喷砂。
|
|
MIXING AND THINNING
|
PE07 is a two pack product, both packs containing the proper ratio of ingredients. The entire contents of each container must be mixed together, as supplied. Stir base first to obtain smooth homogenous condition not longer than 3 minutes. Use the total content of each pack. The use of a speed adjustable power mixer is recommended. However, if necessary due to equipment limitation, thinning is allowed with TH03 (max. 3% v/v)
|
|
混合和稀释
|
PE07是双组份产品，各种成分在使用中有 明确的配比;使用时各种成份必须一起混合.首先搅拌 基料达到光滑均匀，但时间不得超过2分钟，基料达 到均匀状态后缓慢地加入固化剂，须连续搅拌三分钟. 使用每罐全部涂料的可使用速度可调的电动搅拌机， 过度搅拌会加速固化，降低产品的寿命。不建议进行 稀释.但是,如果由于设备局限性,可以用TH03进行稀释.
|
|
APPLICATION.
|
PE07,can be applied by airless spray. DO NOT APPLY OVER WET SUPFACES OR UNDER HUMID CONDITIONS,Ventilation It is very important for the safety of the applicator and the proper performance of EURO-PE07 that good ventilation be provided to all portions of the enclosed area . Dry air IS a must since EURO-PE07, must Not be applied with humidity over 85%
|
|
涂装
|
PE07， 可以采用无气喷涂。 不要在湿表面或潮湿条件下施工 通风对于施工人员的安全，密闭区域的各部分有 良好有通风是很重要的。空气必须是干燥的， 不能在湿度超过85%条件下施工。
|
|
SAFETY
|
WARNIGN: Cause eye and skin irritation. Reaction vapour may cause respiratory irritation in sensitive individuals. May cause allergic skin reaction. Avoid breathing vapours. Do not get in eyes on skin or clothing, ear eye and skin protective equipment. Use appropriate respirator, it is recommended to avoid potential respiratory, preferably mouth-to-mouth, and call physician. BURNS: Exothermic reaction causes product to heat which is normal. Be careful handling after mixing product. Use gloves. FIRST AID: In case of eye contact immediately flush with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash skin contact area with soap.
|
|
安全措施
|
警告:会引起眼睛和皮肤的刺激.反应的蒸汽可能会引起 过敏人群的呼吸道刺激.可能会引起皮肤过敏反应.避免 呼吸蒸汽.请勿触及眼睛、皮肤。要使用眼、耳、 皮肤的防护用具，使用合适的面具，以避免潜在的 呼吸道刺激。使用后用清水彻底的清洗皮肤。如有 不适请咨询医生。衣物再次使用前要洗涤。如果没有 呼吸要进行人工呼吸，最好嘴对嘴，并请医生处理。 灼伤：放热反应会使产品变热，超出正常水平。 在混合后要小心处理。使用手套。 急救：如果不慎接触了眼睛，立即用清水冲洗 至少15分钟，并脱去污染的衣鞋， 用肥皂清洗接触后的皮肤。
|
|
DISCLAMER
|
This is not a specification and all information is given in good faith. Every values presented as Theoretical were calculated from the product formula If requested, can inform any internal measurement method used to determinate any given value presented. Since conditions of use are beyond the manufacturers control information contained herein is without warranty, implied or otherwise, and final determination of the suitability of any information or material for the use contemplated is the sole responsibility of user. The product is intended for professional use only. In case of any doubt, contact your local agent.
|
|
提请注意
|
此文件不是正式的技术文件，所列出的信息是可靠的。 提供的的每个数值都是作为理论数据从产品的配方中 计算出来的。如果需要，可以告知任何上述 给出数据的内部常用测量确定方法。由于使用条件非 生产商所能控制，这里的信息不做为担保。产品只是 用于专业使用。如有任何问题，请与当地代理商联系。 向生产厂咨询详细的施工建议。
|
